Internal Retaining ( Snap ) Ring Sizes and Groove Design Bore Sizes 5.250 - 8.250
The following is Internal Retaining Snap Ring Sizes and Groove Design Chart for industrial applications.
Retaining Ring Groove Dimensional Requirements
Internal Retaining ( Snap ) Ring Size Designations
(All data is in inches.)
Housing Bore |
Ring | Ring Groove |
||||||||
---|---|---|---|---|---|---|---|---|---|---|
Dia. |
Diameter |
Thickness |
Diameter |
Width |
Edge |
|||||
ID |
A |
Tol. | T |
Tol. | OD |
Tol. | S |
Tol. | E |
Tol. |
5.250 |
5.770 |
+.090 |
.125 |
+.004
+.005 |
5.520 |
+.007
+.008
|
.139 |
+.006
----
+.008
|
.405 |
Not more |
Reference: Industrial Retaining Snap Rings, 3100 Series.
All dimensions are in inches. Depth of groove d = (OD-ID)/2. Thickness indicated is for unplated rings; for most plated rings, the maximum ring thickness will not exceed the minimum groove width (S) minus 0.0002 inch. Standard material: carbon spring steel (SAE 1060-1090).
Ring Free Diameter Tolerances: For shaft sizes 0.125 through 0.250, +0.002, −0.004; for sizes 0.276 through 0.500, +0.002, −0.005; for sizes 0.551 through 1.023, +0.005, −0.010; for sizes 1.062 through 1.500, +0.010, −0.015; for sizes 1.562 through 2.000, +0.013, −0.020; for sizes 2.062 through 2.500, +0.015, −0.025; for sizes 2.559 through 5.000, +0.020, −0.030; for sizes 5.250 through 6.000, +0.020, −0.040; for sizes 6.250 through 6.750, +0.020, −0.050; for sizes 7.000 and 7.500, +0.050, −0.130.
Ring Thickness Tolerances: For shaft sizes 0.125 and 0.156, ±0.001; for sizes 0.188 through 1.500, ±0.002; for sizes 1.562 through 5.000, ±0.003; for sizes 5.250 through 6.000, ±0.004; for sizes 6.250 through 7.500, ±0.005.
Groove Diameter Tolerances: For shaft sizes 0.125 through 0.250, ±0.0015; for sizes 0.276 through 0.562, ±0.002; for sizes 0.594 through 1.023, ±0.003; for sizes 1.062 though 1.500, ±0.004; for sizes 1.562 through 2.000, ±0.005; for sizes 2.062 through 5.000, ±0.006; for sizes 5.250 through 6.000, ±0.007; for sizes 6.250 through 7.500, ±0.008.
Groove Width Tolerances: For shaft sizes 0.125 through 0.236, +0.002, −0.000; for sizes 0.250 through 1.023, +0.003, −0.000; for sizes 1.062 through 2.000, +0.004, −0.000; for sizes 2.062 through 5.000, +0.005, −0.000; for sizes 5.250 through 6.000, +0.006, −0.000; for sizes 6.250 through 7.500, +0.008, −0.000.
Related Resources: